Всем привет.
Появились проблемы с иммобилайзером. Однажды машина открылась утром с брелка, я проехал недалеко по делам, и брелка она больше не увидела. Закрыть не удалось, потом завести тоже. Надо нажать кнопку брелка, а брелок не видит.
Ок, думал, села батарейка. Батарейку заменил, в инструкции сказано зажать кнопку открыть и закрыть на 15 секунд, и брелок должен заработать. Не вышло. Сходил домой за вторым ключом, та же история, не работает.
Проковырявшись в интернете весь день, понял что рассинхронизировался BCM.
При этом все манипуляции с переобучением не принесли никакого результата.
Зажать кнопку открывания и повернуть 2 раза ключ в замке зажигания не активирует режим программирования замков, загорается "security" на 4 секунды. 30-минутное переобучение BCM тоже не работает.
Сегодня наткнулся на инструкцию, как запустить машину с европейским иммобилайзером. Оказывается, существует красная карточка с 5-значным кодом, который надо ввести после того, как загорается security. Вводится нажатием на кнопку задних противотуманок. Вот инструкция
To program new FOB for European Blazer you need:
Fob with GM/UTA 15732810
PIN for immobilizer (5 digits) which was included with car papers (probably some red note in service card included with car). Probably you can find 5 digit PIN other way by some service scanner or from Chevy dealer - but I'm not sure that will be easy.
Working car key
Any existing workings FOB's
So proper way to add new FOB for Europe is:
1.Close all doors
2.Insert key into ignition
3.Hold down the power UNLOCK button on the driver's door panel, continue to hold down until instructed to releasein step 9.
4.Perform steps 5 through 8 in a fairly rapid succession.
5.Turn the ignition to the ON position (as far as you can go without starting theengine.)
6.Turn the ignition to the OFF position.
7.Turn the ignition to the ON position (as far as you can go without starting theengine.)
8.Turn the ignition to the OFF position.
9.Release the power UNLOCK button on the door panel. The vehicle should respond by lighting Security on dashboard for about 4 seconds.
10. After Security light turns off input by fog light switch first of five digits from Immobilizer PIN code (5 digits 1-9 - doesnt contains any 0).
11. After about 2 seconds Security light comes on again for about 4 seconds... and after it turns off you have to input second digit... and repeat that step until 5th digit
12. If everything was made correctly the vehicle should respondby door locks locking and unlocking automaticallyly
*** Now you can start your Car without unlocking it by FOB (immobilizer is off for 2 minutes)
13.To program new and existing FOB's hold down the LOCK and UNLOCK buttons on the remote until the doors lock and unlock. This may take up to 60 seconds.
14.Repeat step 13 for each additional remote. (Including any existing remotes).
15.Turn the ignition to the ON position to exit the programming mode.
16.Test all remote(s).
Вопрос. А что делать, если кода нет?
Заказал VXDIAG NANO, попробую найти код в BCM с помощью него. Есть какие-то ещё соображения? Может кто-то уже имел дело с европейками?
Буду благодарен за информацию. И как говорится, не я первый, не я последний